Boatmad.com


Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: JamesM
Forum: General Boating Discussion 23-05-2005, 07:10 PM
Replies: 46
Views: 4,267
Posted By JamesM
:D that was very amusing dude, nice one!!!

:D that was very amusing dude, nice one!!!
Forum: General Boating Discussion 21-05-2005, 12:37 PM
Replies: 46
Views: 4,267
Posted By JamesM
You could try getting someone to sit on the back...

You could try getting someone to sit on the back seat and then move from one side to the other whist going along and see if at any time/positon it cures the chine walking. If this works make note of...
Forum: General Boating Discussion 21-05-2005, 12:27 PM
Replies: 46
Views: 4,267
Posted By JamesM
Should have been this one!!! :D

Should have been this one!!! :D
Forum: General Boating Discussion 21-05-2005, 12:26 PM
Replies: 46
Views: 4,267
Posted By JamesM
oops seems I quoted the wrong person!!!

oops seems I quoted the wrong person!!!
Forum: General Boating Discussion 21-05-2005, 12:24 PM
Replies: 46
Views: 4,267
Posted By JamesM
I have set back on my white P20 cause its a...

I have set back on my white P20 cause its a hydraulic stainless CMC jobbie and its a bit tasty :D

And on the Red one cause it was on there when I bought it and taking it off would mean the...
Forum: General Boating Discussion 21-05-2005, 11:47 AM
Replies: 46
Views: 4,267
Posted By JamesM
Whilst on the subject of bushes and steering...

Whilst on the subject of bushes and steering play, you should check out the motor on the back of Cyes Bernico, its like the sword in the feckin stone. The only person that can move it is the man in...
Forum: General Boating Discussion 21-05-2005, 11:28 AM
Replies: 46
Views: 4,267
Posted By JamesM
I've seen 6750RPM down a nice flat river. But out...

I've seen 6750RPM down a nice flat river. But out at sea 6600 is typical. thats with 1.87:1 gears. 5.5" of set back with the prop shaft about 2 1/2 inches below the bottom of the boat. I reckon thats...
Forum: General Boating Discussion 21-05-2005, 10:41 AM
Replies: 46
Views: 4,267
Posted By JamesM
I use a 22 small hub laser 2 but its been worked...

I use a 22 small hub laser 2 but its been worked to a 22.5 with some cupping and thinning.

I would have ago at re-bleeing the steering you should be able to get the play down to about 1mm. If you...
Forum: General Boating Discussion 21-05-2005, 10:08 AM
Replies: 46
Views: 4,267
Posted By JamesM
Have you checked for play in your recently...

Have you checked for play in your recently installed hydraulic steering? It may need bleeding again.

Check for play in the engine mid section. The bushes may be worn out.

Also try some...
Forum: General Boating Discussion 19-05-2005, 05:31 PM
Replies: 46
Views: 4,267
Posted By JamesM
What does he want to know?

What does he want to know?
Showing results 1 to 10 of 10

 

All times are GMT +1. The time now is 12:26 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
×