Trim tabs - Page 2

Burty · 01-02-2005, 02:11 AM

Quote:

Originally posted by Taz
Cool i have a jack plate to go on my boat wont the st 16 be good enougth with a jackplate?

Should be i have the pro system with the reinforced hoses etc they said it would cope with 300hp not sure about speed.

What system do you have then?

I'm sure the bennett tabs will work but Cycos are better didn't you ever hear the saying "the bigger the better". What does john and tony think??????

Steering. i've got twin cable but not happy with it cus if i run with the engine high it locks up. looking to get hydraulic but don't trust sea star cus it still runs of the 1 bolt. on twin cable i cant turn the steering for a reason if you have sea star you can turn and it may break bolt however thats just my opinion what does everyone else think?

Cyco · 01-02-2005, 08:23 AM

Taz looking at the rear of your boat it could do with a bit of tidying up.
I recently made some custom components for a P20 but the guy never paid up, so I now have for sale some cheap components to suit yours if you want them.
I have a 3mm st/st mirror polished transom plate to suit a mercury V6.
A dash plate & dash top plate in white, similar too Burty's.
Rex marine dial surrounds in blue, Rex grab handle in blue, rex control levers in blue.
A through hull bow tank water pick up.
Oh and a transom tie bar kit (rose jointed) a must for the P20.

As for the tabs the bigger the better as Burty say's, what a difference they make in the rough.
You could fit them to yours quite easily by moving a few thing around.
£500 is a good price for the ST16 but that is one ugly tab.

Didn't get the tabs back last night so no pics as yet.
Been promised them today.

Cyco

Cookee · 01-02-2005, 01:06 PM

Anyone want to quote me a price for some tabs for the race boat - 24' RIB 200hp good for just over 70mph on a good day (it's done 72mph) - the bigger the better but strong as well - I kill stuff, been through 3 offshore saddles in 4 years!

JamesM · 01-02-2005, 01:25 PM

Quote:

Originally posted by Cookee
been through 3 offshore saddles in 4 years!

You ****!!!

Cyco · 01-02-2005, 05:04 PM

You won't break my tabs but I use bennett rams and they aren't that strong.
If you want a bullet proof set up it will cost.
Try 'too old' he had some nice gear for sale.
If you happy with bennett twin rams then mine would work out cheaper and you could have your own custom logo in the tabs at no extra charge.

OK THE PRICE FOR A COMPLETE SET OF 600MM TABS WITH CUSTOM LOGO AND BACKPLATES WITH TWIN RAMS AND TWIN PUMPS FOR FASTER ACTING TABS ALONG WITH ALL HARDWEAR AND SWITCH PANEL WOULD BE .........£961.79

THE SAME SET UP AS ABOVE WITH A SINGLE PUMP WOULD BE £745.34

CYCO

Cyco · 01-02-2005, 05:06 PM

OK HAVE JUST BEEN INFORMED THAT BURTY NEW TABS HAVE ARRIVED SO WILL POST SOME PICS LATER ON AROUND 8.30ish.

Taz · 01-02-2005, 06:10 PM

Cyco pm ed you

Burty · 01-02-2005, 06:34 PM

Quote:

Originally posted by Taz
Cyco pm ed you

O well he wont read that till tomorrow then cus he only goes on boatmad when he's at work

Taz · 01-02-2005, 06:52 PM

Oh dear burty wants these bits cyco has and do you have any pics of some of them on your boat?

Cookee · 01-02-2005, 07:06 PM

OK Cyco - thanks for your reply - I'll get back to you after my trip to the boat show and I've topped up the boat kitty!

Burty · 01-02-2005, 07:21 PM

Quote:

Originally posted by Taz
Oh dear burty wants these bits cyco has and do you have any pics of some of them on your boat?

Its ok dude he wont sell them tonight. I'm seeing him later anyway so i will tell him. If you look at the post called Cyco'd in powerboat gallery you will see my boat during the build it has the dash plates in that. I'll PM you his number and you can phone him if you want